适用范围:配套108/158/102/152机型(包括绗缝绣)pplication range: Matched with 108/158/102/152 (including quilt embroidery)
功能说明:电控系统核心控制电路(CPU板)
Function introduction: Core control circuit of computerized system (CPU)
端口和跳线Ports and Jumpers
端脚定义Pins Definition
端口 Port |
端脚 Pin# |
定 义 Definition |
端口 Port |
端脚 Pin# |
定 义 Definition | ||
CZ601 |
1 |
+5V |
CZ6011 |
1 |
CW(正转/Direction) |
X向步进驱动(X Axis Motor Stepping Driver) | |
2 |
GND |
2 |
CCW(反转/Revesion) | ||||
3 |
+12V |
3 |
PD(限流信号/Current limit) | ||||
4 |
12VGND |
4 |
AL-(步进故障/Stepping diver error) | ||||
CZ605 |
1 |
APL(A相连续脉冲/A phase encoder pulse) |
5 |
AL+(+12V) | |||
2 |
BPL(B相连续脉冲/B phase encoder pulse) |
6 |
12VGND | ||||
3 |
0PL(0位脉冲/0 phase encoder pulse) |
7 |
CW(正转/Direction) |
Y向步进驱动(Y Axis Motor Stepping Driver) | |||
4 |
+5V |
8 |
CCW(反转/Revesion) | ||||
5 |
+5VGND |
9 |
PD(限流信号/Current limit) | ||||
CZ606 |
|
滑差/伺服Electromagnetic/Servo |
变频驱动 FV Drive |
10 |
AL-(步进故障/Stepping diver error) | ||
1 |
RETURN(反馈/Feedback) |
RETURN(反馈/Feedback) |
11 |
AL+(+12V) | |||
2 |
SDJ SP(调速/Speed Adjust) |
SDJ SP(调速/Speed adjust) |
12 |
12VGND | |||
3 |
BRAKE(刹车) |
CCW(反转) |
CZ6012 |
1 |
NC(未使用/No connection) | ||
4 |
START(启动) |
CW(正转) |
2 |
12VGND | |||
5 |
+12V (注1)(Note1) |
+12V |
3 |
GX(勾线/Thread-catching) | |||
6 |
12VGND(注1)(Note1) |
|
4 |
KX(扣线/Thread-holding) | |||
CZ607 |
1 |
HALF RO.(半回转信号/Half rotation) |
5 |
JX(剪线/Thread-trimming) | |||
2 |
+12V |
6 |
HS+(换色电机正转/Color-changing motor CW rotation) | ||||
3 |
12VGND |
7 |
HS-(换色电机反转/ Color-changing motor CCW rotation) | ||||
4 |
12VGND |
8 |
HS R/S(换色电机起停/ Color-changing motor start\stop) | ||||
5 |
N8(8421码第3位/8421 BCD code bit 3) |
CZ6014 |
1 |
START(启动) | |||
6 |
N4(8421码第2位/8421 BCD code bit 2) |
2 |
ADJ SP(调速) | ||||
7 |
N2(8421码第1位/8421 BCD code bit 1) |
3 |
+5V | ||||
8 |
N1(8421码第0位/8421 BCD code bit 0) |
4 |
GND | ||||
CZ608 |
1 |
STOP(停止) |
CZ6015 |
1 |
IN1(勾线回位信号/Thread-catching return) | ||
2 |
SLOW MOVE(慢动) |
2 |
+12V | ||||
3 |
START(启动) |
3 |
12VGND | ||||
4 |
12VGND |
4 |
IN2(剪线回位信号/Thread-trimming return) | ||||
CZ609 |
1 |
DXJC(断线检测/Thread break detecting) |
5 |
+12V | |||
2 |
12VGND |
6 |
12VGND | ||||
3 |
12VGND |
7 |
IN3(扣线回位信号/Thread-holding return) | ||||
4 |
UP(上位/Up-position) |
8 |
+12V | ||||
5 |
MID(中位/Middle-position) |
9 |
12VGND | ||||
6 |
LOW(下位/Low-position) |
CZ6017 |
1 |
+12V | |||
7 |
XJ(线夹信号/Spring switches) |
2 |
12VGND | ||||
8 |
DXQD(断线启动/Thread break startup) |
||||||
9 |
FSW(封上位信号) | ||||||
CZ6010 |
1 |
X+(X正方向限位/+X-Axis direction limit) | |||||
2 |
12VGND | ||||||
3 |
12VGND | ||||||
4 |
Y-(Y负方向限位/-Y-Axis direction limit) | ||||||
5 |
Y+(Y正方向限位/+Y-Axis direction limit) | ||||||
6 |
X-(X负方向限位/-X-Axis direction limit) |
谢谢发帖人。要学习。不知道主板锁了出现北京精大豪控制设备版权所有。用什么软件来解开
欢迎光临 电脑绣花论坛 (http://jindashop.com/) | Powered by Discuz! X3.2 |